brokenujoint
12-28-07, 12:16 PM
Spousal seperation forces sell
all given prices are for reference and are not for individual sell and are NEW
Block 1996-1998 4.0 HO casting number 53020569 250.00
Head- 1991-1995 4.0 HO casting number 7120 150.00
Crankshaft- 1971-1980 12 counterweight crank casting number 3214723 105.00
Crankshaft rear main seal- #05018594AA
Crankshaft pilot bearing with AX-15 or NV3550 transmission- #53009180AB 13.21
Rods- AMC 258 rods # 3180444 71-81 707 casting) 159.00Pistons- Sealed Power 677P +0.020 pistons #STL-677P20 118.04
Piston Rings- Hastings +0.020 cast piston rings #667 20.05
Rod bearings- Clevite 77 rod bearings #CB-960P-20. You’ll need 6 of these. 30.00
Main bearings- Federal Mogul main bearings #FEM-7211M 63.39
Main bearing studs- stock from a donor engine 0.00
Main bearing girdle spacer kit (14 hardened 5/16” steel washers) 1.00
Crankshaft sprocket bolt #83502890 and washer #J3173284 (reused from donor)0.00
Crank harmonic damper #33002920T (reused from donor) 0.00
Timing gear and chain CLO-9-3127 123.69
Oil pump- Melling high volume pump MEL-M167HVS 72.39
Complete Gasket Set- #J 242L-47 includes #CS-5713X and #HS-5713Z 70.84
Camshaft bearings- Clevite 77 camshaft bearings #SH-549S 8.11
Lifters- CRN-99278-12 73.69
Banks header new 400.00
99+ intake manifold 125.00 NEW
68mm Dakota TB mated 100.00 NEW
engine stand 75.00 used
engine cherry picker 120.00 used
the block has been bored out to 0.020 over,honed,maged, acid dip cleaned, freeze plugs installed. its ready to build
the head is port and polished, decked and maged
ALL parts are new
all you'll need is a stock cam, water pump, ignition, and to finish the head with a valve job.
ive got 2 yrs of work on this thing and countless research and parts sourcing and elbow grease on the intake set up and headwork.
so far i have well over 2,400.00 into it and since my fiance and i are splitting and selling the house, its gotta go. i may even sell the jeep.
I WILL NOT PARTOUT.
you're looking at a 260hp stroker set up with over 300 lb of torque. the block and parts are not together. everything is in boxes and is NEW with receipts.
all given prices are for reference and are not for individual sell and are NEW
Block 1996-1998 4.0 HO casting number 53020569 250.00
Head- 1991-1995 4.0 HO casting number 7120 150.00
Crankshaft- 1971-1980 12 counterweight crank casting number 3214723 105.00
Crankshaft rear main seal- #05018594AA
Crankshaft pilot bearing with AX-15 or NV3550 transmission- #53009180AB 13.21
Rods- AMC 258 rods # 3180444 71-81 707 casting) 159.00Pistons- Sealed Power 677P +0.020 pistons #STL-677P20 118.04
Piston Rings- Hastings +0.020 cast piston rings #667 20.05
Rod bearings- Clevite 77 rod bearings #CB-960P-20. You’ll need 6 of these. 30.00
Main bearings- Federal Mogul main bearings #FEM-7211M 63.39
Main bearing studs- stock from a donor engine 0.00
Main bearing girdle spacer kit (14 hardened 5/16” steel washers) 1.00
Crankshaft sprocket bolt #83502890 and washer #J3173284 (reused from donor)0.00
Crank harmonic damper #33002920T (reused from donor) 0.00
Timing gear and chain CLO-9-3127 123.69
Oil pump- Melling high volume pump MEL-M167HVS 72.39
Complete Gasket Set- #J 242L-47 includes #CS-5713X and #HS-5713Z 70.84
Camshaft bearings- Clevite 77 camshaft bearings #SH-549S 8.11
Lifters- CRN-99278-12 73.69
Banks header new 400.00
99+ intake manifold 125.00 NEW
68mm Dakota TB mated 100.00 NEW
engine stand 75.00 used
engine cherry picker 120.00 used
the block has been bored out to 0.020 over,honed,maged, acid dip cleaned, freeze plugs installed. its ready to build
the head is port and polished, decked and maged
ALL parts are new
all you'll need is a stock cam, water pump, ignition, and to finish the head with a valve job.
ive got 2 yrs of work on this thing and countless research and parts sourcing and elbow grease on the intake set up and headwork.
so far i have well over 2,400.00 into it and since my fiance and i are splitting and selling the house, its gotta go. i may even sell the jeep.
I WILL NOT PARTOUT.
you're looking at a 260hp stroker set up with over 300 lb of torque. the block and parts are not together. everything is in boxes and is NEW with receipts.