Announcement

Collapse
No announcement yet.

Nick's CJ build part 1

Collapse

Forum Thread First Post

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Looks like some light at the end of the tunnel.
    Check out .

    Comment


    • The door skin template, is a unique shape. Will you be able to use, Half door windows?

      Everything is coming along nicely.
      It was like that when I got here.

      Comment


      • I'm still amused at how tiny the Reids are. Nice cutting work!
        [COLOR=#ff8c00]MYJEEP(crawls)ROCKS(again).com

        I have finally stopped drinking for good.
        Now I drink for evil..... :devil:
        [/COLOR]

        Comment


        • More stuff...
          We're at the point where a lot of littler tinkery-type stuff gets done. This weekend we re-installed the driveline with new clutch, pressure plate, throw out bearing, fork, etc. Installed a hydraulic master/slave setup for the clutch. Ran some more fuel and brake lines. Painted the engine. Started a new set of billet door hinges.

          Rolled a bead in thsi peice of sheet metal to make a saddle clamp for the steering column.
          20150524_131203 by MJR RAT, on Flickr

          Had to make a pivot pin for the new actuator ram of the clutch master cylinder. Found some roll pins at the local metal supply that fit the bill.
          20150524_145246 by MJR RAT, on Flickr

          20150524_145253 by MJR RAT, on Flickr

          Put the pedal tree back together and in the tub
          20150524_145305 by MJR RAT, on Flickr

          Drilled a 1.5" hole in the firewall next to the Hydroboost for the clutch master and installed it.
          20150524_145320 by MJR RAT, on Flickr

          20150524_145353 by MJR RAT, on Flickr

          20150524_145406 by MJR RAT, on Flickr

          20150524_152137 by MJR RAT, on Flickr

          20150524_152144 by MJR RAT, on Flickr

          20150524_153905 by MJR RAT, on Flickr

          Found a use for the cut off from the Savvy aluminum corners. Bat MoCJ
          20150524_160215 by MJR RAT, on Flickr

          Hell Yes! To the bat cave...
          20150524_160315 by MJR RAT, on Flickr

          Also went through the wiring harness, getting ready to install. There will be some long nights one weekend soon getting this snake pit figured out. Now we wait for some more parts for the suspension/steering, drive shafts and some other stuff. I'll be doing more finish work on the body a get her ready for paint in a couple of weeks.
          [CENTER][COLOR=#ff0000]Resistance Off Road
          [/COLOR]Join the Resistance...
          http://www.resistanceoffroad.us[/CENTER]

          Comment


          • You just really have to appreciate all the work that's going into this Rat rod Jeep

            Comment


            • keep the fins
              [COLOR="#FF0000"]R[/COLOR]edneck [COLOR="#FF0000"]D[/COLOR]riveway [COLOR="#FF0000"]F[/COLOR]ab
              www.DanielBuck.net - www.DNSFAIL.com - www.FurnitureByBuck.com

              Comment


              • awesome. What engine is he going with?

                Comment


                • Steering time again. Changed to the Reid knuckles so a few changes are in order. Looks like some beefy steering for the CJ.
                  20150606_174323 by MJR RAT, on Flickr

                  20150606_174310 by MJR RAT, on Flickr

                  20150606_174246 by MJR RAT, on Flickr

                  Tried two different ways of making the corners look integrated to the tub. The old CJs have a specific contour around the top ledge of the tub that makes it difficult to make the aluminum corners look like they belong. The first was using 1" square tube to fill the gap. Nice, but the second way I like much better. Will be cutting 3/16" aluminum sheet metal to make a top cap that will bolt to the tub and completely cover the gap in a nice, clean manner. Here is the template ready to go:
                  20150606_174334 by MJR RAT, on Flickr
                  [CENTER][COLOR=#ff0000]Resistance Off Road
                  [/COLOR]Join the Resistance...
                  http://www.resistanceoffroad.us[/CENTER]

                  Comment


                  • Damn. It's been a long time since the last post here. Back in July I had knee surgery, then I moved to the new RAM Offroad location in Pinon Hills. So Nickie's CJ has been sitting under a tarp. But we're finally back at it. I'll be posting progress on this build as we go. Lots of changes to come. Like a new engine (per the wifey) and lots of other goodies. Some of the custom parts used on Nick's CJ are available at RAM Off road as well. Check it out at www.ramoffroad.us . Yes, a shameless plug...
                    [CENTER][COLOR=#ff0000]Resistance Off Road
                    [/COLOR]Join the Resistance...
                    http://www.resistanceoffroad.us[/CENTER]

                    Comment


                    • $5 if you keep the fins on Nick's jeep
                      [COLOR="#FF0000"]R[/COLOR]edneck [COLOR="#FF0000"]D[/COLOR]riveway [COLOR="#FF0000"]F[/COLOR]ab
                      www.DanielBuck.net - www.DNSFAIL.com - www.FurnitureByBuck.com

                      Comment


                      • Originally posted by daniel_buck View Post
                        $5 if you keep the fins on Nick's jeep
                        Naaa. He's being all serious and shit...
                        [CENTER][COLOR=#ff0000]Resistance Off Road
                        [/COLOR]Join the Resistance...
                        http://www.resistanceoffroad.us[/CENTER]

                        Comment


                        • V8 Engine?
                          [COLOR=#ff8c00]MYJEEP(crawls)ROCKS(again).com

                          I have finally stopped drinking for good.
                          Now I drink for evil..... :devil:
                          [/COLOR]

                          Comment


                          • Flathead 4, not enough coin to break and fix it

                            Comment


                            • Originally posted by aw12345 View Post
                              Flathead 4, not enough coin to break and fix it
                              [COLOR="#800000"]So true....so true.[/COLOR]
                              [COLOR="darkred"]"Death Smiles at Everyone... Marines Smile Back."
                              Adopt-a-Trail Member.[/COLOR]

                              Comment


                              • Originally posted by USMC 0369 View Post
                                [COLOR="#800000"]So true....so true.[/COLOR]
                                V6 Dauntless. Best choice for you Nick.
                                [CENTER][COLOR=#ff0000]Resistance Off Road
                                [/COLOR]Join the Resistance...
                                http://www.resistanceoffroad.us[/CENTER]

                                Comment

                                Working...
                                X